User Manual
3D PRINTER RECOMMENDED
TEMPERATURE SETTINGS
Kindly note that the perfect way to fine tune the print settings is by
printing a Temperature Tower with the N-fil3D filament on your
printer. The temperature tower shall provide you with the perfect
settings to run your filament for your specific printer. You can
download the STL file from the link below and follow the
instructions mentioned alongwith.
Meterial
PLA
PLA
PLA
PLA
ABS
HIPS
Colour
Polar White
Metallic Series
Clear Series
Other Colours
All Colours
All Colours
Nozzle Temperature
198 oC
204 oC
195 o C
196 o C
230 oC
220 oC
TECHNICAL
DATA SHEET
PLA :
HS PLA Clear Range : Download
HS PLA Fluorosence Range : Download
HS PLA Metallic Range : Download
HS PLA Glow in the Dark : Download
HS PLA Solid Colour Range : Download
HS PLA Matte Pastle Range : Download
Turbo-Finish PLA+ : Download
Ultra Light PLA+ : Download
Silk PLA+ : Download
rPLA (Recycled Filament) : Download
ABS – Download
HIPS – Download
Carbon Fiber – Download
PETG – Download
ABS FR – Download
Nylon – Download
FILAMENT
FILTER
What?
We are enclosing a filament filter with every N-fil3D. The 3D printed Universal Filament Filter is a
casing that contains sponge inside it in order to stop any kind of dust on the surface of the filament
from entering the hot-end. It will clean the filament and eliminate the possibility of clogging (or at
least reducing it by a great margin).
This small device can protect your 3D printer from
a very common issue with filaments in an open
environment – dusty filaments.
Why?
Plastic melts well enough, but dust motes and the occasional grain of salt may become stuck in the extruder. Especially since the nozzle is so
much narrower than the extruder itself (0.3-0.4 mm vs. 1.75 mm).
That means that, over time, enough grime can accumulate in the extruder and the filament could have trouble passing through it.
Needless to say, it can be really annoying for a print to be ruined just because filament stops coming out of the nozzle in the middle of the hoursor days-long process.
Admittedly, some of the newer 3D printers can resume a print, but even then, the resulting defect might not be easy to mask.
How?
Just put the pre-assembled Filament Filter anywhere between the N-fil3D spool and Hot-end. Pass the filament through the filter (as shown in the
image) into the hot-end before loading the filament. You are set to print!
REUSE
DESICCANT
If the desiccant is green: It means that desiccant has absorbed moisture to
it’s full capacity. We need to recharge the desiccants now. To recharge it,
take the desiccants and preheat it in oven or microwave to get rid of the
moisture in it. Kindly dry it until all the granules turn back to orange. Now
you can use it again to keep the N-fil3D filament dry.
Further, the desiccant sachet doesn’t shred any fibre on the filament and is
food-safe too.
We are providing you with two 5 grams sachets of colour changingpremium desiccants. These are not ordinary desiccants. These desiccantsliterally do their job and let you know the efficiency of it upfront too.
DRY INDICATION COLOUR PATTERNS FOR DESICCANT
When you receive the filaments, kindly store the desiccants from the
vacuum pouch safely in the ‘MY PROTECTOR KIT’ provided along the filament.
These orange-coloured desiccants change their colour from orange to
green when they absorb moisture.
If the desiccant is orange: It means you can reuse the desiccant as it is to
absorb more moisture and keep the filament moisture-free when in
storage
Dry
Moist
Wet
MY PROTECTOR
KIT
Desiccant
Filament Filter
Vaccum Bags
Along with every N-fil3D filament, we are providing a ‘My Protector Kit’ to help you store it easily post usage.
Kindly put the two orange coloured desiccants (received in the vacuum pouch) in the ‘My Protector Kit’. Post usage of the N-fil3D filament, kindly put it in kit and seal it.
Store it anywhere you like, it is now safe!
At any time, if you find the desiccants turn green, kindly recharge the desiccants by following the steps mentioned in Point No. 5
SPOOL
Our spool has a unique design. The spool has hexagon cuts which allows for better visibility of filament. Below is a guide which shall let you know the quantity of filament remaining on the spool. Further, it allows you to wind the filament hassle-free anywhere. When you have used up the filament and wish to store it, insert the filament into any hexagon hole nearby maintaining the tension. You need not go all the way up to find the hole, thus much easier to use. <Images of filament with our spool against any other spool
